Need Support? Let’s guide you to the right answer or agent.

OpenTunnel Ideas Portal

ADD A NEW IDEA

All ideas

Showing 1603

Allow automatic POI definition from bearing to bearing (for camber and deflections)

For final bridge plans involving a steel bridge, we need to report dead load deflections at either the 10th or 20th points along the span—from bearing to bearing. While the program does calculate these points, it currently measures them from the e...
29 days ago in OpenBridge Designer 0 Needs review

RMBridge--Seismic Eigen Analysis with CQC Method for Repeated Sub-Systems

In eigenvalue analysis of repetitive structures—where identical sub-systems exist independently within a single model—the same frequencies and eigenmodes are often assigned repeatedly to each sub-system. This leads to an issue with the CQC (Comple...
29 days ago in OpenBridge Designer 0 Needs review

Camber on the beam, Beam need to be curved and follow the underside of the deck without gaps- Australia specific

The current beam hog modeling behavior is not as expected. While deck thickening can be applied, the supporting beams remain straight and do not conform to the underside profile of the deck. In reality, the beams should follow the curved shape of ...
29 days ago in OpenBridge Modeler 0 Needs review

The fatigue stress range calculation doesn’t follow as per AASHTO Table 6.6.1.2.3-1, Section 7.2

LBS V22.00.02.19CS0035224 Service Case 1233802: [CS0035224] The fatigue stress range calculation doesn’t follow as per AASHTO Table 6.6.1.2.3-1, Section 7.2 Product Backlog Item 1233801: (VM):LBS:V22:The fatigue stress range calculation doesn’t fo...
29 days ago in OpenBridge Modeler 0

( OBM > Deck > Thickness variation) Deck variations remain normal to alignment.

I am attempting to model a 3 span concrete slab bridge with thickened haunches over the supports. I am using a typical deck template. My thickness variations are shown in the first attachment. The Bridge has a 10 degree skew angle at the supports....
29 days ago in OpenBridge Modeler 0 Planned

Enhancement to Create a New Lost Civil Rule Icon

In 10.11 R1 (10.11.00.115), the profile projection icon under the OpenRoads Model tab changes when the projection’s source reference file is detached. Once you detach the reference the profile projection loses its civil rule, thus the icon changes...
almost 2 years ago in OpenRail Designer / OpenRoads Designer / OpenSite Designer / User Interface 0 Future consideration

Enhancement::Additional Tool for Design of Cross over connection between Tangent & Canted Tracks

I suggest improvements to Bentley OpenRail Designer for handling Cross over connections in the following scenarios: Cross over Between Adjacent Tangent Tracks: Enable a simple geometric connection between two parallel tracks without the use of Geo...
8 months ago in OpenRail Designer / Turnouts/Crossings 0 Needs review

Snap control for 3d cut profile attachment

We need a snap setting to be active by default for self-attached attachments created by 3d cuts in profiles. Currently, the snap setting is set to off by default, which forces us to always turn it on manually in the attachments dialog, which is an...
over 2 years ago in Geometry / OpenRail Designer / OpenRoads Designer 0 Future consideration

Exported TIN surface must carry same edge method on importing.

Exported surface in TIN format not keeping the same edge method while importing it in new .dgn file. So, it is expected to get such functionality where the exported surface should carry the same edge method or while importing any surface it should...
about 1 year ago in OpenBridge Designer / OpenBridge Modeler / OpenRail Designer / OpenRail Overhead Line Designer / OpenRoads Designer / OpenSite Designer / OpenTunnel Designer / Terrain 1 Future consideration

In Dynamic Sections, add width and cross slope for top of components to pop up window when hovering on components.

In SS2 InRoads Roadway Modeler we used to be able to see component slopes and widths in a pop-up window when hovering on components. This allowed us to quickly test that new point controls (or parametric constraints) were working as intended. It's...
over 2 years ago in OpenRail Designer / OpenRoads Designer / OpenSite Designer 1 Future consideration